The PLANET FT-80X is Fast Ethernet Bridge 100Base-FX fiber to 10/100Base-TX shielded twisted pair (STP) converter. It supports selectable for half-duplex and full-duplex operations and supports a variety of fiber options. The converter auto-adapts to the highest level of performance supported by the device connected to the STP port. When the device is a switch or a workstation that supports full duplex, the converter adapts to the full-duplex mode and provides an effective 200Mbps bandwidth. When the connected device is a hub or a workstation that supports only half duplex, the converter adapts to the half-duplex mode and provides the nominal 100Mbps bandwidth. An override switch provides total manual control over the half/full-duplex operation, in fiber-optic interface. The fiber port of converter operates at 1310 nm and uses ST, SC, MT-RJ, VF-45 or WDM connectors. Multi-mode models that support distances up to 2 km and single-mode models that support distances up to 15/35/50 km are available.
The FT-80x series are with LFP (Link Fault Pass Through function) (LLCF/LLR) and the DIP Switch design. LLCF/LLR can immediately alarm administrators the problem of the link media and provide efficient solution to monitor the net. The DIP Switch provides disable or enable the LFP function.
LLCF (Link Loss Carry Forward) means when a device connected to the converter and the TP line loss the link, the converter's fiber will disconnect the link of transmit. LLR (Link Loss Return) means when a device connected to the converter and the fiber line loss the link, the converter's fiber will disconnect the link of transmit. Both can immediately alarm administrators the problem of the link media and provide efficient solution to monitor the net.
Key Features
Comply with IEEE802.3, IEEE802.3u 10/100Base-TX, 100Base-FX Standard
Connectors: One RJ-45 (Auto-MDI/MDI-X) Twisted Pair, EIA568
One Fiber-optic, 1310nm wavelength, connector-type and distance vary with model.
FT-806A20: Tx-1310nm, Rx-1550nm
FT-806B20: Tx-1550nm, Rx-1310nm
Data Transfer Rate:
TP: 10/100Mbps
FX: 100Mbps
Duplex mode support:
Full or half-duplex mode by Auto- Negotiation (TP)
Full or half-duplex mode by DIP-switch (FX)
LED indicators: PWR, FX LNK/ACT, FX FDX/COL, TP 100, TP LNK/ACT, TP FDX/COL
DIP-switch: 2 DIP-switches
Rear DIP-switch: FX duplex mode selection
Side DIP-switch: LFP (Link Fault Pass-through) mode selection
SPECIFICATION
Product
Model
FT-80x
Protocol
IEEE 802.3u, 100Base-FX, 100Base-TX
Dimensions
70 x 97 x 26 mm (W x D x H)
Weight
0.2kg
Power
5V DC, 2A, max.
Connectors and Cables
Twisted Pair / STP
RJ45, Category 5 (EIA/TIA 568)
Fiber-optic
Vary on model;
X=1,2,3,4,5,6
1:ST
2:SC
3:MT-RJ
4:VF-45
6 Single SC; WDM
Multi-mode cable
50/125, 62.5/125 µm
Single-Mode (SM) cable
9/125 µm
Supported Distances and function
Twisted Pair STP
100 m / 328 ft.
Multi-mode Fiber Optic
412 m / 1,350 ft. (Half-Duplex)
2 km / 1.2 mile. (Full-Duplex)
Single-Mode (SM)
412 m / 1,350 ft. (Half-Duplex)
15 km / 9 mile. (Full-Duplex)
35km / 21 mile. (Full-Duplex)
50km / 31 mile. (Full-Duplex)
Port Mode
TP: Half and Full Duplex, auto-negotiation
FX: Half and Full Duplex via DIP switch
Environmental
Temperature
0 to 50 degrees C
Humidity
5-90% (non-condensing)
Ordering Information
FT-801
100Base-FX to 10/100Base-TX (ST, MM) Bridge Media Converter
FT-802
100Base-FX to 10/100Base-TX (SC, MM) Bridge Media Converter
FT-802S15
100Base-FX to 10/100Base-TX (SC, SM, 15Km) Bridge Media Converter
FT-802S35
100Base-FX to 10/100Base-TX (SC, SM, 35Km) Bridge Media Converter
FT-802S50
100Base-FX to 10/100Base-TX (SC, SM, 50Km) Bridge Media Converter
FT-803
100Base-FX to 10/100Base-TX (MT-RJ, MM) Bridge Media Converter
FT-804
100Base-FX to 10/100Base-TX (VF-45, MM) Bridge Media Converter
FT-806A20 *
100Base-FX to 10/100Base-TX (SC, SM) Bridge Media Converter (TX: 1310)
FT-806B20 *
100Base-FX to 10/100Base-TX (SC, SM) Bridge Media Converter (TX: 1550)
*Remark
FT-806A20/806B20 should runs in pair. It means you must connect FT-806A20 in one end another FT-806B20 in other end.
